DEADBLOCKS
| #89J-203 | WHITACRE
PH16-18-20-22 Deadblock Coiler Unit w/Skin Draft Die; 5 HP motor; max. speed 120 FPM
|
| #89J-431 | K+B 42" Model WDK-42-D
Inverted Downcoiler; 30 HP; cap. .114"-.360"; 125 to 1500 FPM approx.
|
| #89J-443 | Wire Industries 24" and
30" Inverted V-grooved Downcoilers; (4) four 24"; (2) two 30";
Wire dia. range: .050" to .216" on 24"; .312" on 30"; 500 FPM
approx.; 15 HP motors; SCR controls
|
| #89J-444 | 30" MacBee Model #30DB1X40A
Drawing Type Deadblock Coiler, 40HP DC Motor, 1374 FPM; 1993
|
| #89J-455 | Macbee Model
16DBLC-15A Drawing Deadblock; 16" block, 15HP DC motor, wire dia.
coiling range: .047"-.125" (1.2-3.1mm), electric clutch braking system,
dancer control unit
|
| #89J-456 | Whitacre 16" Drawing
Deadblock Coiler; 16" air cooled block; wire dia. range: 1.2-3.1mm
(.047-.125") approx; Baldor 20HP AC motor; 1700 RPM; 230/460V-60-3; Allen
Bradley AC Electrical controls (new 2005)
|
| #89J-457 | Macbee/Whitacre
style Drawing Deadblock Coiler; 22" block x 8" face; flywheel has
multiple wheel guide sheeves; die holder; manual horn lift; 40HP AC Motor
(amps 93.3 - 46.7, 1176 RPM, 230/460 volts); v-belt drive; finish wire dia:
.125"-smaller
|
| #89J-458 | Macbee-Renco style
Drawing Deadblock Coiler; 22" block x 8" face; flywheel has
multiple wheel guides, sheeves, die holder; manual horn lift; air cooled
block (blower fan); 40HP AC Motor, Baldor 3phase induction (amps 98/49, 1180
RPM, 230/460 volts); v-belt pulley; hand roll pointer (16 grooves); finish
wire dia: .125"-smaller
|
| #89J-459 | Morgan DB-16 Drawing
Deadblock Coiler; 22" dia. block x 8" face; max. start dia: .150"
H.C., L.C., alloys; single draft; die mounted on flywheel; 50/30 HP DC
Motor: (1150/2300 RPM, 84/50 amps, 500V); ratio 5.61 to 1; max. speed: 3500
FPM approx.; max. die pull: 1200 lbs.; 4 belt drive pulley unit; manual
lever raise/lower horn; no electrical controls
|
| #89J-460 | Macbee/Renco Style
Drawing Deadblock Coiler; 22" block x 8" face; 50HP AC Induction
Motor (875 RPM, 127/43 amps, 230/460 volts); max. start wire: .187" approx.;
speed: 2100 FPM approx. (not to be exact); single belt drive - motor to
flywheel shaft; manual lift low-raise horn; Allen Bradley SCR controls;
constant torque AC drive
|
| #89J-462 | Renco Double
Block/2-Die Drawing Deadblock Coiler; 22" block x 100HP AC (no
ripper block); .105"-.250" wire dia. start-finish; Allen Bradley controls
|
| #89J-463 | Custom-made (Renco
style) 26" Drawing Deadblock; 40HP DC motor; 1750 RPM; Schultz
relay controls
|
| #89J-464 | Custom-made (Renco
style) 24" Drawing Deadblock; 40HP DC motor; 1750 RPM; Schultz
relay controls
|
| #89J-466 | Renco 26" Drawing
Deadblock Coiler; model 26DB-60; 60HP DC motor; 1750 RPM; Schultz
relay electrical controls
|
| #89J-467 | Custom-made (Renco
style) 26" Drawing Deadblock Coilers; air cooled block (blower
fan); 75HP DC motor; 1750 RPM; Schultz relay electrical controls; 2
available - (1) with controls, (1) without controls
|
| #89J-468 | Ernst Koch 28"
(700mm) Drawing Deadblock Coiler; model KEWS IV-2; 1 draft; 14-16%;
max. inlet 5.3-7mm, .208"-.280"; min. finish: .135" (3.4mm); high carbon;
2800 FPM (14M/sec); water cooled block; water cooled die; 100HP DC motor;
480V-3-60cycle; Mentor PLC electrical controls; turntable
|
| #89J-469 | (20) Macbee Inverted V-grooved Take-up Downcoilers, Model 26BGCTU7-1/2; 26" v-grooved blocks; 10 sets of 2; each block driven by 7-1/2HP DC motor; wire dia. range: 2.0 to 4.5mm approx.-not to be exact; speeds: 5 to 250FPM approx; no turntables |
Gavlick Machinery Corporation |
| 100 Franklin Street, Bristol, Connecticut 06010, USA |
| Phone: 860-589-2900 Fax: 860-589-0863 |
| e-mail: sales@gavlick.com home: www.gavlick.com |
